In addition to the fertilizer selected for fertilization should be carried out according to the requirements, the fertilization skills are also very important. Do not splash the fertilizer solution on the long-lived flower leaves, otherwise it is easy to cause the leaves to rot(plastic nursery pots); but sometimes it is inevitable that the fertilizer solution will be splashed on the leaves due to careless operation, at this time, it should be washed off immediately with water. Compared with the fertilization of other potted flowers and plants, the fertilization of potted longevity flowers often needs to be more careful, because there are some differences in fertilization.
If the light intensity is not strong, it is recommended to provide sufficient light for it, which is very important for plant growth. However, when the summer temperature is up to 30 ° C, and the light intensity is too strong, it is necessary to timely take shade treatment and spray water to moisturize and cool down. Otherwise, the plant will enter the dormancy state under high temperature environment, so the plant becomes very slow. When the temperature is as low as 15 ° C, measures should be taken to keep warm and keep warm in time, especially in the low temperature environment in winter.
When planting, a part of the soil shall be placed under the basin first, and the planting shall be started from one side of the basin, and evenly planted in the basin. Generally speaking, the tiger skin orchid must change the basin every two years, or carry on the branch propagation. Cutting and branching are the most commonly used methods of propagation(plastic nursery pots wholesale). Compared with leaf cutting propagation, the biggest advantage of branching propagation is that it can keep Phnom Penh of Phnom Penh, which is generally carried out in combination with basin change in spring.
If the selected soil is relatively fertile and the base fertilizer is added during planting, the nutrient elements needed for its growth are basically enough, but if the soil is relatively poor, some fertilizer can be applied appropriately. When Basil grows 4-6 leaves, the fertilizer should be mainly thin fertilizer and water, the purpose is to promote the growth of its root. Only when the root development is relatively fast and perfect, its growth will be more vigorous.
Jasmine Flowers naturally turn yellow because of lack of nutrients. To change the basin for jasmine, the soil can be rich humus soil, such as pine needle soil and so on(plastic nursery pots manufacturers). Excessive fertilization will cause root burning, which will naturally cause the yellow leaves of jasmine, while too little fertilization will cause the yellow leaves of jasmine. If the fertilizer is too much, increase the amount of water to dissolve the concentrated fertilizer, or put the flowerpot into a large container to soak for about 1 minute.
It is necessary to select varieties with good quality, heat resistance, early resistance, fast growth and disease resistance because of the high temperature, drought or strong storm and rain. Select the protected land with sunshade facilities as the cultivation land, or cover the coriander with straw after sowing, uncover the straw after emergence, build a small flat shed with a height of 60-70cm, and cover with sunshade net. The sandy loam with high terrain, rich in organic matter, loose soil, good water and fertilizer conservation is the best.
The bulbs are placed in the middle of the basin, the buds are upward, the bulbs are evenly distributed, the buds are slightly towards the basin wall (to prevent the buds from squeezing in the middle after they come out of the basin), and the bulbs are covered with soil of 6-8cm (planted in winter) or 8-10cm (planted in summer). Because the water and nutrients are mainly absorbed by the rhizomes during the growth of lilies(black plastic nursery pots), the covering soil must not be too shallow, otherwise the rhizomes are not long and the final shadow is not good The growth of crinoid is easy to fall.
For the branches with more flower buds, the fertilization concentration must not exceed 0.3%, mainly P and K, which results in the loss of leaves of rubber trees mostly due to water and soil problems(square grow pots).
Whether it has been watered too much recently and whether the weather is wet, which causes the water in the basin to evaporate.By using similar methods, we can first rule out whether there are problems in the three links of water, soil and fertilizer.
It needs to use the form of scattered light to get some light properly.
In recent years, the lower end of the cuttings should be left 3cm to 5cm and cut into a slanting mouth(plug trays wholesale).
It can increase the application of P and K fertilizer to enhance the cold resistance of winter crops.If the early maturing varieties can stop sowing by using the strip sowing method, the strip sowing method can use tools to open a shallow ditch with a depth of 3cm on the ridge surface or on the ridge platform, and spread the seeds into the shallow ditch.
Stop covering with fine soil (3 rows of soybeans can be planted on the border surface), and use the roller on the border surface Just roll it on the ridge once.The optimum temperature for rooting of cuttings is 20 ℃ ~ 30 ℃.
Sneha Nursery is one of the Best Plant Nursery in Hyderabad which provides high-quality Flower seedlings, Flower pots, Fruit plants, healthy plants.we are the Best Plants Nursery in Hyderabad to takes care about our Healthy seedlings, Fruit seedlings routinely to keep them healthy
Low-density PE bags are moisture-permeable, The air permeability is larger, and the high-density PE bag is smaller.
The advantages of PE bags are economy, cheapness, and good moisture resistance.
It is best to use polyethylene bags to add a layer of external packaging that can block light and have low air permeability, such as synthetic paper cans, iron cans, etc.
In the early days, they were mainly used for the outer packaging of tea bags with PE bags .
Synthetic paper cans Synthetic paper cans are currently the most widely used packaging materials.
Only air and moisture permeability are still high, and it is not suitable to be used alone.
