logo
logo
Sign in

asnjscos

avatar
[email protected] dream1234567890
asnjscos

Simple tips on how to paint a cosplay accessory cleaner

What cosplayers like to ask is whether they show off their paint cosplay props like a cosplay booth store. So, I create a cosplay tutorial to show how to do it. It is very convenient and you can follow these four steps while spraying, especially if you are painting wood paint RWBY cosplay sword, or Devil May Cry cosplay big sword.

For this cosplay tutorial, use. Before you start painting, you need to prepare the prop. Be sure to polish the prop. If the surface is defective, insert a wood filler. When dry, sand with sandpaper. Repeat this process until you feel ready to paint. Also, wipe the prop with a damp cloth before painting.

 

 

Before you start painting, place something in the work area before you start working. Spray paint spreads throughout. And do not forget that there is proper ventilation. Cosplay props order.

When you are ready, you can start priming. Priming is necessary to increase the adhesion of the paint to the surface of what you are painting. Wood is essential because it is very porous and only absorbs paint. Also, using multiple light coats, as opposed to one or two thick coats, reduces the problem.

Added the first coat of primer, but now everything is dry. Wood grain, filler, etc. will still be seen. No need to worry, it should be like that. Now, take out your 400 grit sandpaper and send it lightly as you don't want to sand the primer, just lubricate it. When that's done, spray all the dust from the cosplay costume mail order recommendations and work. Now re-spray the work. Are no longer displayed.

Now that you have a clean uniform coat, do you want to start painting now? Not enough yet. Sand the primer smoothly. Special care must be taken not to sand the primer. My props. Take compressed air and blow away dust. If wet with sandpaper, remove paper towels and dry props

If you need a different color for different areas of the prop, mask it with green painter tape. Obtain a plastic with a tapered edge and move it along the edge of the masking tape. Helps sticky sticks and prevents paint from seeping down. Laying the tape after each coat may not be a bad idea so that the paint does not integrate with the tape.

When you paint, you basically do the same things as for priming, straight motion, and light coat.

Added the first coat of paint to the prop. Obviously, there is no uniform coat yet. Always check for defects and driving. Take 800 grit sandpaper and gently sand with sandpaper. Smooth everything up to the primer. Grab compressed air and blow dust. Repeat painting until a clean uniform coat is formed.
Wet polishing does not require as coarse a grain of 1000 sandpapers, but prepare a cup or some kind of container and fill it with water. Next, wet the prop. Wet the cup clean. Sand the prop lightly. I don't want to remove the paint, so make it smooth. Leave the sandpaper in the water. Something new. When all is done, remove the cloth or paper towel and go to the cosplay shop.

Go to the last part. Get a clear coat. If it is shiny, just spray on the prop. Again, a light coat is more effective. No running is required. If you are not using varnish, remove the selected brush. When soaking the brush in the varnish, wipe off any excess brush before applying the varnish. If you are using varnish, it is very important to use a thin coat. If you want to avoid runs on all coats, varnish runs are cumbersome and difficult to remove. You need to coat a few times. Light sanding between coats is not a bad idea. Use 800 grit.

https://anigacos.blogspot.com/2020/01/blog-post_20.html

https://anigacos.seesaa.net/article/473202641.html?1579537883

https://ja.stackoverflow.com/questions/62406/cosanigacosdd

collect
0
avatar
[email protected] dream1234567890
guide
Zupyak is the world’s largest content marketing community, with over 400 000 members and 3 million articles. Explore and get your content discovered.
Read more