Sachiya Steel International is one of the prominent Manufacture of high quality Stainless Steel 310H Wire Mesh, which Good resistance to mildly corrosive atmospheres, but significantly less than Grade 310H due to the Sulphur addition; the sulphide inclusions act as pit initiation sites. Grade 310 should not be exposed to marine or other similar environments, as these will result in rapid pitting corrosion. Because the sulphide inclusions in 310 are primarily aligned along the rolling direction the corrosion resistance is particularly reduced in cross-sections.
It is like other common austenitic stainless steels, is subject to stress corrosion cracking in chloride containing environments above about 50°C. Good oxidation resistance in intermittent service to 760°C and in continuous service to 870°C. Not generally recommended but, if unavoidable use Grade 308L or 309 electrodes. AS 1554.6 does not pre-qualify welding of 303. Welds must be annealed for maximum corrosion resistance, but even then poor mechanical and corrosion properties will result.
For ultra-high machining rates there are also available special grade variants such as Ugima 303UX. This includes copper to reduce the work hardening rate, in addition to the usual high Sulphur and Improved Machinability steel making practices. Nuts and bolts. Bushings. Shafts. Electrical switchgear components. Gears. In general any component that is heavily machined and where the corrosion resistance and fabrication properties of 310H are viable. Grade 310H (UNS S31009) has a carbon content restricted to exclude the lower end of the 310 range, so is the grade of choice for high temperature applications.
|
SS 310H Wire mesh Specifications
|
||
| Specifications | : | ASTM A 164 ASME SA 164 |
| Standard | : | DIN, ASTM, BS and all International Standards |
| Length | : | 30m to 100″ |
| Width | : | 1m to 48″ |
| Type | : | Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc. |
| Grade | C | Mn | Si | P | S | Cr | Mo | Ni | N |
| SS 310H | 0.04 – 0.10 | 2 max | 1.00 max | 0.045 max | 0.030 max | 24.00 – 26.00 | – | 19.00 – 21.00 | 53.885 min |
| Density | Melting Point | Tensile Strength | Yield Strength (0.2%Offset) | Elongation |
| 7.9 g/cm3 | 1402 °C (2555 °F) | Psi – 75000 , MPa – 515 | Psi – 30000 , MPa – 205 | 40% |
| STANDARD | WERKSTOFF NR. | UNS | JIS | BS | GOST | AFNOR | EN |
| SS 310H | – | S31009 | – | – | – | – | – |
- Off-Shore Oil Drilling Companies
- Power Generation
- Petrochemicals
- Gas Processing
- Specialty Chemicals
- Pharmaceuticals
- Pharmaceutical Equipment
- Chemical Equipment
- Sea Water Equipment
- Heat Exchangers
- Condensers
- Pulp and Paper Industry
Sachiya Steel International is one of the well-established Manufacture and Exporter for Stainless Steel 904L Wire Mesh, which is a harden able high – carbon chromium steel.
When put under heat treatment, Stainless Steel 904L Hexagonal Wire Mesh attains the highest hardness levels of any grade of stainless steel.
Resistance to sulphuric acid is particularly exceptional, but Stainless Steel 904L Welding Wire Mesh shows useful resistance in phosphoric acid, nitric acid as well as in chloride environments.
SS 904L Netting Wire Mesh has good mechanical properties at both ambient and elevated temperatures, up to approximately 930 Degree F (500 Degree C) and is readily fabricated by usual industrial processes.Stainless Steel 904L Woven Wire Mesh is composed of carbon, chromium, copper, iron, manganese, molybdenum, nickel, phosphorous, silicon, and Sulphur.
Application of SS 904L Spring Steel Wire Mesh could result in real cost savings when carefully compared to higher – cost alloys to determine if the necessary resistance is obtained in the chosen media.
Post weld heat treatment of SS 904L Fencing Wire Mesh may not be required for use in some corrosive environments due to resistance to inter – granular corrosion in the as-welded condition.
