Top Six Common PCB Assembly Deficiencies and How to Conflict Them.

The J-STD-001 certification is an industry traceable program that falls under the PCB assembly and famous as the industry’s most robust assembly standard for PCB.

Let's read about its benefits for instructors/technicians here…

Factors of increasing the value of automotive PCBIn recent years, the trend of automobile electrification and electronics has become more and more obvious.

As the backbone of electronic products, the importance of PCB manufacturing in the automotive supply chain is also increasing day by day.

Compared with traditional fuel vehicles, the addition of charging, energy storage, power distribution and voltage conversion equipment for new energy vehicles will bring a large number of new application scenarios to PCBs.At the same time, although autonomous driving above L4 cannot be mass-produced in a short time, the gradual penetration of a variety of intelligent driving components will bring rapid development opportunities for the application of high-end high-frequency PCBs in automobiles.According to calculations by relevant departments, only in the powertrain and transmission fields, the value of PCBs on electric vehicles is as high as about RMB 800 per bicycle, which is 20 times the value of PCBs in this field of traditional vehicles.The new demand for electric vehicles mainly comes from powertrain related equipment-on-board chargers, battery management systems (BMS), voltage conversion systems (DC-DC, inverters, etc.)

and other high-voltage and low-voltage devices.Factors of increasing automotive PCB productionA large number of high-voltage and high-power devices contained in new energy vehicles, such as IGBTs and MOSFETs, have high requirements for heat dissipation, which makes the layout of PCBs not too dense, which further increases the amount of PCBs for new energy vehicles.On each new energy vehicle, the total PCB board required for the above-mentioned equipment alone amounts to about 0.8 square meters.However, the total PCB required for a medium-level electronic fuel vehicle is only about 0.43 square meters.

In the internal combustion engine and traditional system of traditional fuel vehicles, the amount of PCB used is very small, only about 0.04 square meters in total, which has greatly increased the output of automotive PCB.According to calculations by relevant departments, the PCB consumption of new energy vehicles equipped with millimeter-wave radar and large central control screens will reach 1.24 square meters, worth 1281 yuan, which is 3.6 times that of traditional fuel vehicles without the above configuration.Factors contributing to the considerable growth rate of China's pcb marketThe production and sales of China's new energy passenger vehicles will continue to grow rapidly in the next few years, and the CAGR is expected to be around 40% in 2018-2025.

The domestic new energy passenger vehicle sales exceeded 1 million in 2018, and it is expected to exceed 2.5 million by 2020, and close to 12 million by 2025, with a market share of more than 40%.Major domestic PCB manufacturers have a relatively complete layout in the fields of automotive infotainment, lighting, powertrain and chassis (steering and braking).It is estimated that by 2025, the global automotive PCB market will reach 58.3 billion yuan, and China is expected to reach 40 billion yuan.

Product launch strategy & how to do them just like Apple, an effective launch strategy that sets you up to achieve your goals.

Click here to know more about us!

PCBs and PCB assemblies are everywhere in today’s electronics industry.

Find out why partnering with Kingstec gives you the best of both worlds for your contract assembly and manufacturing needs.

Rush PCB offers you a unique full turnkey PCB assembly in UK.

We are specialize in turnkey circuit boards assembly in high layer count PCBs services.More Info:- https://www.rushpcb.co.uk/full-turnkey-pcb/Contact US:-3 Charlotte Court,Claremont Lane,Esher, Surrey,KT10 9AG,UKPHone no:-0203 750 0201E-mail:[email protected] or [email protected]

Spacing between wiresIn terms of the processing capacity of the PCB manufacturer, the minimum spacing between wires should not be less than 3mil.

From a production point of view, the bigger the better if possible, the more common is 10mil.2.

The aperture tolerance is slightly different depending on the plate, generally it can be controlled within 0.05mm, and the minimum pad width should not be less than 0.2mm.If it is a large area of copper, it usually needs to be retracted from the edge of the board, generally set to 20mil.

In the PCB design and manufacturing industry, under normal circumstances, due to the mechanical considerations of the finished circuit board, or to avoid curling or electrical short-circuiting due to the exposed copper skin on the edge of the board, engineers often spread copper on a large area The block is shrunk by 20 mils relative to the edge of the board instead of spreading the copper to the edge of the board.There are many ways to deal with this kind of copper shrinkage, such as drawing a keepout layer on the edge of the board, and then setting the distance between the copper paving and the keepout.

Here is a simple method to set different safety distances for copper paving objects.

For example, the safety distance of the whole board is set to 10mil, and the copper paving is set to 20mil, and the effect of 20mil shrinkage of the board edge can be achieved.

PCB Supplier - Rush PCB is the most trusted and innovative PCB manufacturer and assembler service in Australia.

Over 20 years experience in manufacturing high-quality PCB board and assembly service.Visit our website:- https://www.rushpcb.com.au/Contact UsMelbourne VIC 3000Email: [email protected]: +61 3 8399 9167