sachiya steel

sachiya steel

Sachiya Steel International are manufacturers suppliers dealers exporters of Pipes,Tubes ,Pipe Fitting, Fasteners.

Followers 1
Following 0
Sachiya Steel International is one of the prominent Manufacture of high quality Stainless Steel 310H Wire Mesh, which Good resistance to mildly corrosive atmospheres, but significantly less than Grade 310H due to the Sulphur addition; the sulphide inclusions act as pit initiation sites.Grade 310 should not be exposed to marine or other similar environments, as these will result in rapid pitting corrosion.Because the sulphide inclusions in 310 are primarily aligned along the rolling direction the corrosion resistance is particularly reduced in cross-sections.It is like other common austenitic stainless steels, is subject to stress corrosion cracking in chloride containing environments above about 50°C.Good oxidation resistance in intermittent service to 760°C and in continuous service to 870°C.Welds must be annealed for maximum corrosion resistance, but even then poor mechanical and corrosion properties will result.For ultra-high machining rates there are also available special grade variants such as Ugima 303UX.This includes copper to reduce the work hardening rate, in addition to the usual high Sulphur and Improved Machinability steel making practices.
Sachiya Steel International is one of the prominent manufacturers for Stainless Steel 316 Wire Mesh, which is a relatively rare form of corrosion which requires a very specific combination of tensile stress, temperature and corrosive species, often the chloride ion, for it to occur.Typical applications where SCC can occur in Stainless Steel 316 Hexagonal Wire Mesh are hot water tanks and swimming pools.Another form known as sulphide stress corrosion cracking (SSCC) in Stainless Steel 316L Welding Wire Mesh is associated with hydrogen sulphide in oil and gas exploration and production.This is now quite a rare form of corrosion, where if the Carbon level in SS 316 Netting Wire Mesh is too high, Chromium can combine with Carbon to form Chromium Carbide.This occurs at temperatures between about 450 Degree C – 850 Degree C in Stainless Steel 316L Woven Wire Mesh, where this process is also called sensitization and typically occurs during welding.The Chromium available to form the passive layer in SS 316 Spring Steel Wire Mesh is effectively reduced and corrosion can occur.SS 316L Fencing Wire Mesh is avoided by choosing a low carbon grade the so-called ‘L’ grades or by using steel with Titanium or Niobium which preferentially combines by means of Carbon.Stainless Steel 316 Wire Mesh is rather like a battery and can accelerate corrosion of the less ‘noble’ metal.
Sachiya Steel International is one of the leading Manufacture And Exporter of high quality Stainless Steel 304 Wire Mesh, which allows to be matched for corrosion resistance with the austenitic and ferritic steel grades.Stainless Steel 304 Hexagonal Wire Mesh is always important to assess the suitability of a particular with a full knowledge of the corrosive environment.Structures of SS 304 Welding Wire Mesh in swimming pools are known to be prone to SCC.The use of standard austenitic SS 304 Netting Wire Mesh is forbidden in several applications.The advantage of high strength in Stainless Steel 304 Woven Wire Mesh immediately becomes a disadvantage when considering formability and machinability.The high strength of Stainless Steel 304 Spring Steel Wire Mesh also comes with lower ductility than austenitic grades.SS 304 Wire Mesh has very limited use in hydrochloric acid because of the risk of uniform and localized corrosion.High – alloyed steels such as 304 SS Wire Mesh can be used in dilute hydrochloric acid.
Sachiya Steel International is among renowned Manufacture and Exporter for Stainless Steel 304L Wire Mesh, which are used as they are not sensitive to inter – granular corrosion after heating within the carbide precipitation range of 425 Degree C – 850 Degree C. Our Stainless Steel 304L Hexagonal Wire Mesh is the grade of choice for applications in the temperature range of up to about 900 Degree C, combining high strength, resistance to scaling and phase stability by means of resistance to subsequent aqueous corrosion.A limitation with this SS 304L Welding Wire Mesh is that titanium does not transfer well across a high temperature arc, so is not recommended as a welding consumable.Our Stainless Steel 304L Netting Wire Mesh is stabilized in contradiction of chromium carbide formation by the addition of titanium.These Stainless Steel 304L Woven Wire Mesh is heat resistant, titanium stabilized, austenitic alloy that’s commonly used for service in the 1000 Degree F – 1600 Degree F temperature range.Our SS 304L Spring Steel Wire Mesh is primarily used in applications that involve continuous and intermittent service temperatures within the carbide precipitation range of 800 Degree F – 1500 Degree F.  These SS 304L Fencing Wire Mesh was developed for use in the chromium carbide precipitation range of 1800 Degree F – 1500 Degree F (427 Degree C – 816 Degree C) where un – stabilized alloys are subject to inter – granular attack.SS 304L Wiremesh SpecificationsSpecifications:ASTM A 164 ASME SA 164Standard:DIN, ASTM, BS and all International StandardsLength:30m to 100″Width:1m to 48″Type:Wire Mesh , Hexagonal Wiremesh, Welding Wiremesh, Netting Wiremesh, Woven Wiremesh , Spring Steel wire mesh, Fencing Wiremesh etc.304L Stainless Steel Wire Mesh Chemical CompositionGradeCMnSiPSCrMoNiN304Lmin.–––––18.0–8.0–max.0.032.01.000.0450.0320.012.0– Stainless Steel 304L Wiremesh Mechanical Properties GradeTensile Strength (MPa) minYield Strength 0.2% Proof (MPa) minElongation (% in 50mm) minHardnessRockwell B (HR B) maxBrinell (HB) max304L4851704092201 Equivalent Grades for 304L Stainless Steel Wiremesh GradeUNS NoOld BritishEuronormSwedish SSJapanese JISBSEnNoName304LS30403304S1158E1.4301X5CrNi18-102332SUS 304L  SS 304L Wire Mesh Application Industries Off-Shore Oil Drilling CompaniesPower GenerationPetrochemicalsGas ProcessingSpecialty ChemicalsPharmaceuticalsPharmaceutical EquipmentChemical EquipmentSea Water EquipmentHeat ExchangersCondensersPulp and Paper Industry
Sachiya Steel International is one of the well-known manufacturers for high quality Stainless Steel 310 Wire Mesh, which contain 16 percent to 26 percent chromium and up to 35 percent nickel, which, like manganese, is a strong austenite.SS 310 Hexagonal Wire Mesh has characteristics from an invisible, self – healing chromium oxide film that forms when chromium is added at concentrations greater than 10.5 percent.The best corrosion resistance is obtained in this austenitic Stainless Steel 310S Welding Wire Mesh, where their microstructures consist of very clean crystals in which all alloying elements are held in solid solution.Austenitic SS 310 Netting Wire Mesh cannot be hardened by heat treatment; they are also nonmagnetic.The ferritic and martensitic Stainless Steel 310S Woven Wire Mesh both have an excellent microstructure, where the latter has a higher carbon level and can be hardened and is used for knives and tools.Stainless Steel 310 Spring Steel Wire Mesh contain only up to 0.12 percent carbon, which also have chromium as their main alloy addition and practically no nickel.Corrosion resistance of this Stainless Steel 310S Fencing Wire Mesh is modest, and they are ferromagnetic.
Sachiya Steel International is one of the well-known Manufacture & Exporter in Stainless Steel 304H Wire Mesh, which contains niobium for stabilization against sensitization and resultant inter – granular corrosion.SS 304H Hexagonal Wire Mesh is a nickel – iron – chromium austenitic alloy that was developed for maximum resistance to acid attack, specifically sulphuric acid.SS 304H Welding Wire Mesh has excellent resistance to general corrosion, pitting, and crevice corrosion in chemicals containing chlorides and sulphuric, phosphoric, and nitric acids.Although originally designed for use in sulphuric acid related industries, Stainless Steel 304H Netting Wire Mesh is now a popular choice for a wide variety of industries including the chemical, food, pharmaceutical, and plastics industries.In addition, Stainless Steel 304H Woven Wire Mesh is used in heat exchangers, mixing tanks, metal cleaning and pickling equipment, and piping.Stainless Steel 304H Spring Steel Wire Mesh is great for corrosion resistance, which further appears to fall between both the stainless and nickel categories as it contains characteristics of both.SS 304H Fencing Wire Mesh is often chosen to solve stress corrosion cracking problems, which may occur with other alloys.Our SS 304H Wire Mesh was designed for maximum resistance to acid attack and demonstrates superior resistance to stress – corrosion cracking in boiling 2 0% to 40 % sulphuric acid, and also has excellent general corrosion resistance to sulphuric acid and to chloride stress corrosion cracking.SS 304H Wire mesh SpecificationsSpecifications:ASTM A 164 ASME SA 164Standard:DIN, ASTM, BS and all International StandardsLength:30m to 100″Width:1m to 48″Type:Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc.
Sachiya Steel International is one of the prominent exporter & wholesaler of Stainless Steel 304L Screw, is the lower carbon version of the alloy.Stainless Steel 304L Hex Head Screws was developed for enhanced creep resistance and for higher strength at temperatures above 1000 Degree F (537 Degree C).Stainless Steel 304L Socket Head Cap Screws does not perform well in chloride solutions, even in small concentrations, or in sulphuric acid.Stainless Steel 304L Socket Set Screws should be considered for applications requiring intermittent heating between 800 Degree F (427 Degree C) and 1650 Degree F (899 Degree C), or for welding under conditions which prevent a post – weld anneal.The high temperature oxidation resistance of Stainless Steel 304L Anchor Screws is similar to that of other stainless steels.Stainless Steel 304L Blind Rivet Screws cannot be hardened by heat treatment, only by cold working.Stainless Steel 304L Concrete Screws can be easily welded and processed by standard shop fabrication practices.Often in many product forms, the grain size and carbon content of Stainless Steel 304L Threaded Screws can meet excellent requirements of clients.
Sachiya Steel International is the top most Manufacture & Exporter in Stainless Steel 304 Screw , which has slightly improved corrosion resistance over stainless steel 321 screws in strongly oxidizing environments.Stainless Steel 304 Hex Head Screws is also advantageous for high temperature service because of its good mechanical properties.Stainless Steel 304 Socket Head Cap Screws offers higher creep and stress rupture properties than Stainless Steel 317 Screws, which might also be considered for exposures where sensitization and inter – granular corrosion are concerns.Stainless Steel 304 Socket Set Screws is a columbium (niobium) / tantalum stabilized austenitic chromium – nickel stainless steel which was developed to provide an 18 – 8 type alloy with improved inter – granular – corrosion resistance.Stainless Steel 304 Anchor Screws has a slightly improved corrosion resistance over other alloys of stainless steel in strongly oxidizing environments as a result of the addition of columbium (niobium) and tantalum.Stainless Steel 304 Blind Rivet Screws is the higher carbon (0.04 – 0.10) version of the alloy, which does not perform well in chloride solutions, even in small concentrations, or in sulphuric acid.Stainless Steel 304 Concrete Screws was developed for enhanced creep resistance and for higher strength at temperatures above 1000 Degree F (537 Degree C).In most instances, the carbon content of Stainless Steel 304 Threaded Screws enables dual certification.
Sachiya Steel International is a known Manufacture and exporter of Carbon Steel A694 Socket Weld Fittings, which can be welded by all the common arc welding processes.These ASTM A694 Carbon Steel Forged Socket Weld Elbow Fitting meets the tensile properties and also meets Charpy impact toughness in minimum at -50 Degree C (-58 Degree F).To obtain good impact toughness after welding, our ASME SA 694 Carbon Steel Forged Socket Weld Tee Fittings requires a higher level of impact toughness in the parent material.Sachiya Steel International is also one of the well – known manufacturer and trader of these ASTM A694 Carbon Steel Forged Socket Weld Cap Fitting, which is usually used in the as welded condition using weld filler.Our ASME SA 694  Carbon Steel Forged Socket Weld Coupling Fittings is superior to the more expensive grades and is also superior at most concentrations.These ASTM A694 Carbon Steel Forged Socket Weld Cross Fittings also compares favorably to high silicon austenitic stainless steels in hot concentrated sulphuric acid.The iso – corrosion curves shows corrosion lines for our ASME SA 6944 Carbon Steel Forged Socket Weld Union Fittings and other alloys in dilute sulphuric and concentrated sulphuric acid.
Sachiya Steel International is one of the pioneer seller and trader of Duplex S32205 Socket Weld Fittings, which is available at reasonable price for our esteemed clients.Chloride stress corrosion cracking of Duplex S31803 Forged Socket Weld Elbow Fittings can occur when the necessary conditions of temperature, tensile stress, oxygen, and chlorides are present.Because these conditions in Duplex S32205 Forged Socket Weld Tee Fittings are not easily controlled and are often characteristic of the operating environment, SCC has sometimes been a barrier to the use of stainless steels.Duplex S31803 Forged Socket Weld Cap Fittings are especially susceptible to SCC, and even Type 317L is not resistant.However, the duplex nature of Duplex S32205 Forged Socket Weld Coupling Fitting imparts an excellent resistance to SCC.Duplex S31803 Forged Socket Weld Cross Fittings resists SCC in two sodium chloride-containing environments that provide meaningful results relating to many practical service applications.As with most austenitic stainless steels, these Duplex S32205 Forged Socket Weld Union Fittings will not resist boiling 42 % magnesium chloride, but this environment is rarely encountered in service.The boiling magnesium chloride test results indicate only that Duplex S31803 Forged Socket Weld Plug Fittings can be susceptible to SCC in certain specific environments.
Sachiya Steel International is a known distributor and supplier of Carbon Steel A350 Socket Weld Fittings, where a common engineering design criterion is that its corrosion rate should not exceed.ASTM A350 Carbon Steel Forged Socket Weld Elbow Fittings is similar to the parent metal, but contains 2 % to 2.5 % extra nickel to ensure that the weld metal retains a 50 / 50 phase balance.This is reflected in the design stresses for ASME SA 105 Carbon Steel Forged Socket Weld Tee Fittings that it is the widely used code for piping.Like all high alloy materials, ASTM A350 Carbon Steel Forged Socket Weld Cap Fitting requires care in welding.It should only be fabricated by qualified welders working to approved procedures.ASME SA 105 Carbon Steel Forged Socket Weld Coupling Fittings is recommended that qualification should be excellent but should include a corrosion test in addition to the usual mechanical and NDE requirements.The curves show that ASTM A350 Carbon Steel Forged Socket Weld Cross Fittings offers superior performance in both dilute and concentrated acids.
Sachiya Steel International is a known distributor and supplier of Carbon Steel A105 Socket Weld Fittings, where a common engineering design criterion is that its corrosion rate should not exceed.ASTM A105 Carbon Steel Forged Socket Weld Elbow Fitting is similar to the parent metal, but contains 2 % to 2.5 % extra nickel to ensure that the weld metal retains a 50 / 50 phase balance.This is reflected in the design stresses for ASME SA 105 Carbon Steel Forged Socket Weld Tee Fitting that it is the widely used code for piping.Like all high alloy materials, ASTM A105 Carbon Steel Forged Socket Weld Cap Fittings requires care in welding.It should only be fabricated by qualified welders working to approved procedures.ASME SA 105 Carbon Steel Forged Socket Weld Coupling Fitting is recommended that qualification should be excellent but should include a corrosion test in addition to the usual mechanical and NDE requirements.The curves show that ASTM A105 Carbon Steel Forged Socket Weld Cross Fittings offers superior performance in both dilute and concentrated acids.
Sachiya Steel International is one of the pioneer distributor and dealer of quality Nickel Alloy 201 Forged Socket Weld Fittings, which is a silvery – white metal with a slight golden tinge that takes a high polish.Nickel 201 Forged Socket Weld Elbow is slowly oxidized by air at room temperature and is considered corrosion – resistant.Historically, Nickel 201 Forged Socket Weld Tee has been used for plating iron and brass, coating chemistry equipment, and manufacturing certain alloys that retain a high silvery polish, such as German silver.About 6 % of world production of Nickel 201 Forged Socket Weld Cap is still used for corrosion – resistant pure – nickel plating, where these nickel – plated objects sometimes provoke nickel allergy.Nickel 201 Forged Socket Weld Coupling has been widely used in coins, though its rising price has led to some replacement with cheaper metals in recent years.Nickel 201 Forged Socket Weld Cross is one of four elements (iron, cobalt, nickel, and gadolinium) that are ferromagnetic at approximately room temperature.Alnico permanent magnets based partly on Nickel 201 Forged Socket Weld Tee are of intermediate strength between iron-based permanent magnets and rare – earth magnets.Nickel 201 Forged Socket Weld Union is valuable in modern times chiefly in alloys, where about maximum percentage of world production is used in nickel – steels (particularly stainless steel).
Sachiya Steel International is one of the pioneer seller and distributor of quality Nickel 200 Socket Weld Fittings , which has outstanding resistance to hydrochloric acid at all concentrations and temperatures.Furthermore, Nickel 200 Forged Socket Weld Elbow has greatly improved structural stability compared with other type alloys, leading to fewer concerns during welding, fabrication, and service.Nickel 200 Forged Socket Weld Tee is a nickel – molybdenum alloy with excellent resistance to pitting, corrosion, and stress – corrosion cracking plus, thermal stability superior to that of alloy.Nickel 200 Forged Socket Weld Cap is applicable in aircraft, furnace and chemical process components, honeycombs and gas turbine combustion section components.Nickel 200 Forged Socket Weld Coupling also withstands sulphuric, acetic, formic and phosphoric acids and other non – oxidizing media.Nickel 200 Forged Socket Weld Cross has a special chemistry designed to achieve a level of thermal stability greatly superior to that of its predecessors.Nickel 200 Forged Socket Weld Union has been primarily used for their resistance to corrosion in non – oxidizing environments such as HCl.Nickel 200 Forged Socket Weld Plug is an additional member of the Ni – Mo – family of alloys with a special chemistry designed.
Sachiya Steel International is one of the pioneer seller and trader of Duplex S31803 Socket Weld Fittings, which is available at reasonable price for our esteemed clients.Chloride stress corrosion cracking of Duplex S31803 Forged Socket Weld Elbow Fittings can occur when the necessary conditions of temperature, tensile stress, oxygen, and chlorides are present.Because these conditions in Duplex S32205 Forged Socket Weld Tee Fittings are not easily controlled and are often characteristic of the operating environment, SCC has sometimes been a barrier to the use of stainless steels.Duplex S31803 Forged Socket Weld Cap Fittings are especially susceptible to SCC, and even Type 317L is not resistant.However, the duplex nature of Duplex S32205 Forged Socket Weld Coupling Fittings imparts an excellent resistance to SCC.Duplex S31803 Forged Socket Weld Cross Fittings resists SCC in two sodium chloride-containing environments that provide meaningful results relating to many practical service applications.As with most austenitic stainless steels, these Duplex S32205 Forged Socket Weld Union Fittings will not resist boiling 42 % magnesium chloride, but this environment is rarely encountered in service.The boiling magnesium chloride test results indicate only that Duplex S31803 Forged Socket Weld Plug Fittings can be susceptible to SCC in certain specific environments.
Sachiya Steel International is one of the well-known manufacturing house and trader of Super Duplex S32750 Socket Weld Fittings , where the corrosively of such solutions is affected by acidity and chloride content.In aqueous solutions containing hydrogen sulphide and chlorides, stress corrosion cracking can also occur on Super Duplex S32750 Forged Socket Weld Elbow Fittings at temperatures below 60 Degree C (140 Degree F).In direct contrast to the case with ordinary chloride – induced stress corrosion cracking, ferritic stainless steels such as Super Duplex S32760 Forged Socket Weld Tee Fittings are more sensitive to this type of stress corrosion cracking than austenitic steels.In accordance with solution annealed and liquid quenched wrought Super Duplex S32750 Forged Socket Weld Cap Fittings are suitable for use at temperatures up to 450 Degree F (232 Degree C) in sour environments in oil and gas production, if the partial pressure of hydrogen sulphide does not exceed.Hydrogen Induced Stress Cracking (HISC) in Super Duplex S32760 Forged Socket Weld Coupling Fittings is an embrittlement phenomenon which may occur in catholically protected subsea steel constructions in the presence of high tensile stresses.When connected to catholically protected carbon steels, Super Duplex S32750 Forged Socket Weld Cross Fittings will also be catholically protected even though this is not necessary.The low, ambient, and elevated temperature are mechanical properties of Super Duplex S32760 Forged Socket Weld Union Fittings.Super Duplex S32750/S32760 Forged Socket weld Fitting SpecificationsSpecifications:ASTM A182 & ASME SA182Size:1/8” NB to 4” NB (Socketweld & Screwed-Threaded)Standards:ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799Class:2000 LBS, 3000 LBS, 6000 LBS, 9000 LBSType:Socketweld FittingsGrades:S32750 / S32760/ S32950 A182 Gr F51 / F52 / F53 / F54 / F55 / F57 / F59 / F60 / F61 Super Duplex S32750/S32760 Forged Socket weld Fittings Chemical CompositionGradeCMnSiPSCrMoNiNCuS32750/S327600.030max 1.20 max0.80 max0.035max0.020 max24.0-26.0 3.0-5.0 6.0-8.00.24/0.320.50 Super Duplex S32750/S32760 Socket weld Fitting Mechanical Properties GradesDensity (g/cm 3)Melting PointYield Strength (0.2%Offset)Tensile StrengthElongationS32750 / S327607.8 g/cm31350 °C (2460 °F)Psi – 80000 , MPa – 550Psi – 116000 , MPa – 80015%  
Sachiya Steel International provides a vast collection of Titanium Grade 5 Socket Weld Fittings, where we provide these products to our valuable clienteles in different specifications at industry – leading prices.Titanium Grade 5 Forged Socket Weld Elbow Fitting has outstanding resistance to corrosion in seawater making it an exceptional select for use in subsea oil & gas and offshore processes where seawater weight and corrosion are concerns.Titanium Grade 5 Forged Socket Weld Tee Fittings is age hardenable by heat action to attain even greater powers.Titanium Grade 5 Forged Socket Weld Cap Fitting is used in medical, aerospace, and other uses where reasonable strength, good potency to weight, and promising corrosion features are essential.Titanium Grade 5 Forged Socket Weld Cross Fittings also has some best features to offer such as precise dimensions, easy to fit, rust proof and more.Meanwhile, Titanium Grade 5 Forged Socket Weld Coupling Fitting are also being offered in different sizes and shapes to our customers.Titanium Grade 5 Forged Socket Weld Union Fittings is the common name for a number of different alloys used in corrosive environments.Titanium Grade 5 Forged Socket Weld Plug Fitting is used to keep food surfaces and medical devices safe of microbes as it is self-repairing with its chromium oxide film.
Sachiya Steel International offers superior quality of Titanium Grade 2 Socket Weld Fittings, where our engineers hire cutting – edge technology in the manufacture procedure to make these products.As a single – stage material, features of Titanium Grade 2 Forged Socket Weld Elbow Fittings are measured by chemistry (interstitial contamination and iron elements) and grain size.Linked to the other grades of commercially untainted titanium, Titanium Grade 2 Forged Socket Weld Tee Fittings is feebler than Grade 3 to some extent, but sturdier than Grade 1 and similarly resistant to corrosion.Titanium Grade 2 Forged Socket Weld Cap Fittings is generally used in Marine and Chemical applications, Aerospace industry, Medical industry, Electroplating industry, etc.Meanwhile, Titanium Grade 2 Forged Socket Weld Coupling Fitting are also being offered in different sizes and shapes to our customers.The parts of Titanium Grade 2 Forged Socket Weld Union Fittings have good strength – to – weight ratio, corrosion resistance and ductility.Parts built with Titanium Grade 2 Forged Socket Weld Plug Fitting can be machined, shot – peened and polished in as – built and heat treated states.These Titanium Grade 2 Forged Socket Weld Cross Fittings is widely used in heat exchangers; where despite the low thermal conductivity of titanium the efficiency of heat transfer is high due to good strength, high resistance to erosion corrosion and the fouling resistance of the hard, smooth surface.
Sachiya Steel International is a known manufacturer of Copper Socket Weld Fittings, which are precisely – engineered by our experts using high quality steel, which are in fact made from the reliable experts of the market.We are one of the topmost known trusted names in market that offer these Copper Socket Weld Elbow Fittings, where we have been able to meet varied requirements of patrons in prompt manner.The Air Conditioning Copper Socket Weld Tee Fittings that we manufacture are extensively used in Air conditioning systems.We are passionately engaged in offering an extensive range of these Copper Socket Weld Cap Fittings, which are manufactured from optimum quality material in complete compliance with international quality standards.According to the requirements of our customers, we are involved in offering a fine quality Copper Socket Weld Coupling Fitting.Having vast experience in this domain, we are engaged in offering these elegantly designed Copper Socket Weld Cross Fitting in the market.Our Copper Socket Weld Union Fittings are often used for Writing Instrument, CNG / LPG Kit Industries, Water Lines, Plumbing & Home Application office Accessories & etc.These Copper Socket Weld Plug Fitting are also used for Sanitation, Hot and Cold Water, Industrial & Medical Gas Transportation, Various Engineering, where further we are also engaged in providing HVAC Installation Work and Ducting Work to our valuable clients.
Sachiya Steel International is one of the pioneer trader & dealer for high quality Brass Socket Weld Fittings, where too little carbon content leaves (pure) iron quite soft, ductile, and weak.Brass Socket Weld Elbow Fittings is also distinguishable from wrought iron (now largely obsolete), which may contain a small amount of carbon but large amounts of slag.Carbon contents higher than those of Brass Socket Weld Tee Fittings make an alloy, commonly called pig iron that is brittle (not malleable).While iron alloyed with carbon is called carbon steel, Brass Socket Weld Cap Fittings is steel to which other alloying elements have been intentionally added to modify the characteristics of steel.Common alloying elements of Brass Socket Weld Coupling Fittings include: manganese, nickel, chromium, molybdenum, boron, titanium, vanadium, tungsten, cobalt, and niobium.Additional elements are also important in Brass Socket Weld Cross Fittings: phosphorus, Sulphur, silicon, and traces of oxygen, nitrogen, and copper, that are most frequently considered undesirable.With modern steelmaking techniques such as powder metal forming in Brass Socket Weld Union Fittings, it is possible to make very high – carbon (and other alloy material) steels, but such are not common.Brass Socket Weld Plug Fittings is not malleable even when hot, but it can be formed by casting as it has a lower melting point than steel and good castability properties.
More

Top