Blodgett Oven Installation Procedure
Cooking in a Blodgett convection oven is different from cooking in a conventional deck or range oven since heated air is constantly recirculated over the product by a fan in an enclosed chamber. The moving air continually strips away the layer of cool air surrounding the product and quickly allowing the heat to penetrate. The result is a high-quality product, cooking at a lower temperature in a shorter amount of time. Now, check out how to install a Blodgett convection oven.
Oven Location
If you placed the oven at the proper level. Then, it will give the long-term operator convenience and satisfactory performance.
You need to maintain the below clearances between the oven and combustible or non-combustible construction.
Oven body right side - 1 inch.
Body left side - 1 inch.
Oven body back - 7.5 inches
Body bottom - 4.5 inches
Make sure there will be an adequate air supply to the oven to provide a sufficient flow of combustion and ventilation air.
The area where you have to place the oven that should be free of drafts.
Try to keep the area free as well as clear of all combustibles such as cardboard, paper, solvents, and flammable liquids.
Don't place the unit on a curb base or seal to a wall. Because this will restrict the flow of air and prevent ventilation. An excessive ambient temperature on the right side of the oven caused to tripping of the blower motor's thermal overload device. So, you should correct this condition to avoid permanent damage to the unit.
Leg Attachment
Need to push your oven onto a lift with the bottom of the unit down.
Align the threaded stud in each leg with the nut located inside each bottom corner of the oven's frame. Now, turn the legs clockwise and tighten to the nearest full turn.
You have to align the two-leg plate holes in each leg with those in the oven bottom. Fix the leg with two 1/2" bolts.
Now, level the Blodgett oven by screwing the adjustable leg feet in or out as necessary.
Blodgett Oven Assembly
Secure the short legs to the bottom sections.
Place the upper section in position on top of the lower oven.
You have to place the clips over the edge of your oven frames.
Tighten the clips by bolting together with 3/8" bolts and nuts provided.
Now, attach the flue connector.
Gas Host Restraint
If the Blodgett oven is mounted on casters, you should use a commercial flexible connector with a min of 1.9 cm inside diameter along with a quick-connect device.
You will get this restraint along with the oven that is used to limit the oven's movement. So, no strain is placed upon the flexible connector. Installation of the restraint with a fully stretched connector is easy and quick connect.
The restraint should be attached without damaging the building. Don't use the electrical conduit or gas piping for the attachment of the restraint's permanent end.
Mount the bracket to the leg bolt just below the gas inlet. And, attach the clip-on restraining cable to the mounting bracket.
Final Words
That’s all about Blodgett oven installation. However, the installation should be done by a professional or expert to avoid dangerous problems. If you need further more assistance, you can refer to your Blodgett oven manual. Installation instructions may vary from model to model.
BASO pilot switches are used on all gas-fired and standing pilot equipment that requires the main burner to shut off when the pilot is extinguished.
Typical applications include domestic central heating and commercial space heating appliances as well as industrial processing equipment.These pilot switches monitor the pilot flame through the use of a thermocouple.
In 100% shutoff model applications, if the pilot flame is extinguished, then the switch will be interrupted gas flow to the pilot burner as well as the main burner and caused for shutting down the appliance.In non- 100% shutoff model applications, the switch will interrupt gas flow to the main burner only when the pilot flame is extinguished.
Moreover, it will automatically close and restore service upon resumption of a normal pilot flame.
L61 models are available with Single Pole Double Throw switching actions when an additional switching function like a need of signal light.
BASO Safety Shutoff Device InstallationBefore starting the installation process, you should turn off the power to the appliance.Shut off the gas at the main manual shutoff valve adjacent to the appliance.Remove the device cover by loosening the screws at the side.Now, mount the switch in any convenient position using the mounting holes provided.Push the circuit wires through the conduit opening on the bottom of the device.
Are you searching for replacement parts for farming equipment?
Quality Farms Supply is extremely proud to continue its old age legacy of supplying top-quality farming machinery parts & accessories that suits an extensive range of operations.
Whenever you are searching for top-notch quality and most reliable combine parts, agricultural parts suppliers deliver your products with a guarantee of long service life.
Are you looking for advice on how to find a medical equipment replacement parts dealer?
PhiGEM Parts is dedicated to offering high-quality medical equipment servicing.
Replacement components for medical equipment can be found at PhiGEM Parts.
Take a look at our website.
We are regularly adding new medical imaging parts to our inventory.
