3 Hacks To Keep Your Power Cords Intact

Electrical and electronic devices have become part of everyday life nowadays. This means that you have power cables all over which can be used in solar panels well, be it in the office or at home. If these cables are not well organized, they can create accidents or even wear out too fast. 

You do not want your power cables falling all over and tripping people. At the same time, you want them to last longer as the cost of buying new ones frequently can be overwhelming. 

Power cords can be a headache to handle. No matter how much you try to organize them properly, they always seem to entangle or fray at the edges. If you wrap them, you risk cutting the wires inside, and if you leave them loose, they are more likely to entangle. Also, one can use an extension cord if your LCD is far away from the main switch and watch FUBO Channels for watching sports.

So, what is the secret to handling your power cord properly so that they remain intact and last longer? 

How to Keep Your Power Codes Intact 

1. Wrap it Loosely

Most people wrap their power cords around the power brick. While this may make them look neat and safe, as you repeat the process over and over again, the wires inside will break. 

The problem with repeatedly wrapping the cord the same way is that it creates weak points. With time, your cord will break due to the stress. Instead of wrapping your cord tightly, consider loosening the bend around the power brick a bit. 

If you have time on your side, you can even wrap it using the over-under method, but this is too much work and is really not necessary. Once your cable is wrapped neatly, use some Velcro or a clip to hold the end of the loop in place. 

You can also wrap it in a loose figure-eight shape and tie the open end at the middle of the figure. It comes down to individual preference. So, you can experiment and find out what works for you. 

While at it, be gentle. Avoid stepping on the cable, yanking it from the wall, or bending it too tightly in one direction. This level of caution will prevent the cable from kinking at any point. 

2. Binder Clips

If you are looking for a simple, cheap way to organize your charger cables, there is an excellent solution for you: binder clips! Binder clips are simple to use and customizable as well. 

Before you bind your cables, you need first to coil them into a neat batch. You can then clip them together before storing them away. This will ensure that they do not entangle and form a messy knot when you need them later. 

If you are using the cords, you can attach them to a shelf, table, or desk after clipping. The clips help hold the power cord onto the edge of the desk. If you have cables that often fall into tight spaces when disconnected, this is an incredible hack. 

Once you pass the cables through the clips, they will never fall at the back of the desk again. The clip holds them every time you disconnect them from your device. 

Binder clips are great because they can provide various solutions and keep your office or home neat. Your cables will always be held at the ready. You can also group your lines using binder clips and route them in different directions. 

For just a few bucks, binder clips provide one of the cheapest power cord hacks you’ll find around.  

3. Prevent Fraying

One of the most common problems with phone and laptop power cables is fraying. Maybe this is because these cables are moved around a lot. Think about it; you go with your phone and laptop cables almost everywhere you take your devices. That back-and-forth movement definitely takes a toll on the casing. 

Frayed cables are not only untidy but also dangerous. When the casing comes off, it exposes the wires inside, which can easily break and contact each other. This presents a risk both to the use and the device. 

Given the cost of buying new cables every often, you can take specific steps to prevent your lines from fraying. 

• Roll a spring around the cable

If you have a clickable ink pen, you can open it up and take out the spring. The spring is not long enough but will still help, especially at the cable's edge, where fraying begins. Stretch the spring to increase its length a bit. Next, slide the line through it until it sits nicely within. 

• The paracord trick!

This is an even better solution because you can cover the entire cord. To hack this, get a paracord and cut it open to remove the white strand as you do not need it. 

Melt the edges of the paracord with a lighter to stop it from fraying. Once done, just weave it around your power cord. 

Conclusion

It is almost impossible to get a durable power cable for modern devices. If you use your device a lot, you will find yourself buying new cords practically yearly. But you can prevent this and save cash by implementing the above tips to extend your power cord's life.